UART

Found under IO on the device's panel list.

UART Log

Live log of bytes received on the UART, with a manual send.

The screen

A scrolling log fills the screen, oldest at the top and newest at the bottom. Each line is a chunk of received bytes shown in hex, printed as they arrive.

Controls

Button	Action
Yellow	Send - opens a hex-entry box and sends the bytes you type out the UART
Gray	Open the Logic Analyzer view
PAGE	Open the Logic Analyzer view
Cancel	This help page

HOME leaves the screen from here, as it does everywhere else in the menu. Green, Blue and Red carry no label on this screen and do nothing.

Reading the log

Incoming bytes are grouped as they are received and logged as space-separated hex pairs, up to 32 bytes per line.

Send (Yellow) opens a text box for entering bytes as hex, separated by spaces, commas or tabs (48 49 or 48,49), up to 16 bytes. Entering something that is not valid hex, or more than 16 bytes, rejects the input with a message and sends nothing. A successful send prints its own Tx) line with the bytes sent - the line means the bytes were handed to the UART, not that anything on the other end received them. There is no separate receive line for it either: a sent line only shows up a second time if it is wired back into the receive pin, which is a quick way to confirm a loopback or a device that echoes what it receives.

What persists

The log only fills in while this screen is on the display; leaving it stops new bytes from being recorded, and nothing received while it is closed is kept. Baud rate and other wiring details are set from the UART settings menu, not from this screen.

Logic Analyzer view

Gray or PAGE switch to a Logic Analyzer view of the UART lines (TX, RX, CTS, RTS), with a title line showing the mode, sample rate and capture state. A labelled Back button on that view returns here.

Power

This screen needs the FPGA power zone (6) - the UART header lines route through the FPGA. Opening this screen switches that rail on if it was off, without asking; until it is up nothing sent reaches the header pins even though it still logs a Tx) line. That only happens once, on entry: nothing here re-checks the zone, or the header pins' IO direction, before a Send goes out. Zone 6 is on by default and is also switched from Power Devices.

Logic Analyzer

Captures a burst of digital pins over time and draws them as waveforms, so you can see fast signal changes a live view would miss.

The screen

A title line across the top names what this view is doing: the mode it is capturing, the sample rate, and its state - for example "SPI analyzer 1M idle", changing to armed once you start a capture and to done once the capture lands. Once a capture is loaded, the title also adds a position, such as "done 2/4", showing which slice of the buffer the trace below is panned to.

Below the title, each row is one channel: its name on the left, its waveform trace beside it. Which pins appear here, and what they are named, depends on which tool you opened this screen from. Once a capture lands, a red vertical line marks the sample where the trigger fired.

On screens with a long channel list - GPIO in particular - Up and Down move a highlighted row, shown with a gray band behind its name, and whichever channel is highlighted when you arm a capture becomes its trigger source. On screens with only a few channels, there is no highlighted row: Up and Down do nothing here, and the trigger source is always the first channel shown.

The title costs some of the screen's height, so the GPIO capture - the one with the longest channel list, 13 rows - now shows 12 at a time and scrolls with Up and Down to reach the last one. The shorter protocol channel lists still show every row at once.

Controls

Button	Action
Yellow	Cycle the trigger edge: rising, falling, or none (one-shot)
Green	Cycle the capture rate: 10M, 1M, 100k, or 10k samples per second
Blue	Arm the capture, or stop it while armed
Red	Force the trigger while armed
Left / Right	Pan through a finished capture
Gray / Page	Back - returns to the protocol panel this view was opened from
Cancel	This help page

Red forces the trigger and keeps its Trig label to say so. Home leaves the app from here the same as it does everywhere else.

Capturing

Blue arms the capture - its label changes from Arm to Stop while armed - and waits for the trigger condition set by Yellow on its trigger source (see The screen above for how that source is chosen): a rising edge, a falling edge, or none, which starts capturing right away without waiting for either. Red forces the trigger early if you do not want to wait for it. Green sets how fast the capture samples, from 10 million samples a second down to 10 thousand; faster rates see less time but finer detail.

Capture depth

The sample buffer behind a capture is a fixed size, so the number of samples it holds depends on how many channels you are watching, not just the rate - fewer channels leaves room for more samples in the same buffer. A faster rate always covers less time, and how much less depends on that channel count.

After a capture

Once a capture lands, the waveform fills the screen with the trigger point placed roughly three-quarters of the way across, so more of what happened before the trigger is visible than after it. Left and Right step the view through the rest of the buffer around it; before a capture finishes, they do nothing.

Shared by several tools

This screen appears inside several different tools - GPIO, I2C, SPI, UART and MDIO all open it with their own Page button, each showing that tool's own pins or bus signals as the channels here. Gray or Page on this screen returns you to whichever one opened it.

The capture itself runs on the RP2350's own PIO hardware, not the FPGA, so opening this screen never needs the FPGA power zone. SPI, UART, GPIO and MDIO route their own header lines through the FPGA and need that zone regardless of this screen; I2C reaches the header directly and needs no FPGA zone at all.

See also: UART — the console/GUI commands for this panel.